Language:
繁體中文
English
日文
說明(常見問題)
南開科技大學
圖書館首頁
編目中圖書申請
登入
回首頁
切換:
標籤
|
MARC模式
|
ISBD
非軸對稱無壓皺板深引伸製程模具設計之研究 = Study on the ...
~
張馨文
非軸對稱無壓皺板深引伸製程模具設計之研究 = Study on the die design of a non-axisymmetric deep drawing process without blankholder
紀錄類型:
書目-語言資料,印刷品 : 單行本
並列題名:
Study on the die design of a non-axisymmetric deep drawing process without blankholder
作者:
張馨文,
其他作者:
管金談,
出版地:
[南投縣]
出版者:
南開科技大學車輛與機電產業研究所; 精密模具與機械產業研發碩士專班;
出版年:
民101[2012]
面頁冊數:
9,45葉 : 圖,表 ; 31公分+1張光碟
標題:
非軸對稱深引伸
標題:
Non-Axisymmetric Deep Drawing
電子資源:
http://handle.ncl.edu.tw/11296/ndltd/03051673664760810602
附註:
指導教授: 管金談
附註:
參考書目: 葉43-45
摘要註:
一般深引伸製程為防止板料起皺,常使用壓皺板,但此舉會造成模具較為複雜、引伸負荷增大、模具較易磨損及板料引伸易於破裂等缺點,因此無壓皺板之深引伸製程自有其優勢。本文利用有限元素法研究無壓皺板之非軸對稱深引伸製程模具設計,探討傳統倒圓角模具、圓錐形模具、成形品外形掃出錐型模具、成形品外形掃出Tractrix型模具、成形品外形掃出具反曲點曲線模具等五種模具對非軸對稱深引伸成形負荷、最大板料起皺壓應力、成形品破裂參數及成形品高度分佈等之影響。
非軸對稱無壓皺板深引伸製程模具設計之研究 = Study on the die design of a non-axisymmetric deep drawing process without blankholder
張, 馨文
非軸對稱無壓皺板深引伸製程模具設計之研究
= Study on the die design of a non-axisymmetric deep drawing process without blankholder / 張馨文 - [南投縣] : 南開科技大學車輛與機電產業研究所, 民101[2012]. - 9,45葉 ; 圖,表 ; 31公分.
指導教授: 管金談參考書目: 葉43-45.
非軸對稱深引伸Non-Axisymmetric Deep Drawing
管, 金談
非軸對稱無壓皺板深引伸製程模具設計之研究 = Study on the die design of a non-axisymmetric deep drawing process without blankholder
LDR
:02809pam0 2200289 450
001
125520
005
20150109114530.0
009
00146580
010
0
$b
精裝
099
$a
100NKUT7162007
100
$a
20120814y2012 k y0chiy08 e
101
0
$a
chi
102
$a
tw
105
$a
ak am 000yy
200
1
$a
非軸對稱無壓皺板深引伸製程模具設計之研究
$d
Study on the die design of a non-axisymmetric deep drawing process without blankholder
$f
張馨文
$z
eng
210
$a
[南投縣]
$c
南開科技大學車輛與機電產業研究所
$c
精密模具與機械產業研發碩士專班
$d
民101[2012]
215
0
$a
9,45葉
$c
圖,表
$d
31公分
$e
1張光碟
300
$a
指導教授: 管金談
300
$a
參考書目: 葉43-45
328
$a
碩士論文--南開科技大學車輛與機電產業研究所
330
$a
一般深引伸製程為防止板料起皺,常使用壓皺板,但此舉會造成模具較為複雜、引伸負荷增大、模具較易磨損及板料引伸易於破裂等缺點,因此無壓皺板之深引伸製程自有其優勢。本文利用有限元素法研究無壓皺板之非軸對稱深引伸製程模具設計,探討傳統倒圓角模具、圓錐形模具、成形品外形掃出錐型模具、成形品外形掃出Tractrix型模具、成形品外形掃出具反曲點曲線模具等五種模具對非軸對稱深引伸成形負荷、最大板料起皺壓應力、成形品破裂參數及成形品高度分佈等之影響。
$u
To avoid wrinkling in traditional deep drawing process, a blankholder is used generally. But that will be more complicated in the dies construction, more high in the drawing load, more wear in the drawing die and easily fracture in the workpiece. Therefore, there are some advantages to a drawing process without the blankholder. In this paper, the finite element method is adopted to study the die shape design of a non-axisymmetric deep drawing process without the blankholder. A series of simulations on the non-symmetric deep drawing with a traditional die, a circular cone die, a die by sweeping the product profile along an oblique line, a die by sweeping the product profile along a tractrix curve and a die by sweeping the product profile along a reflection curve, respectively, using the program DEFORM 3D was carried out. The influences of the die parameters such as die angle, die length on the drawing load, the maximum tangential compressive stress of the workpiece, the maximum damage value of the drawn cup and the height distribution of the drawn cup are investigated.
510
1
$a
Study on the Die Design of a Non-Axisymmetric Deep Drawing Process without Blankholder
$z
eng
610
# 0
$a
非軸對稱深引伸
610
# 1
$a
Non-Axisymmetric Deep Drawing
681
$a
000
$b
1140:2
700
1
$a
張
$b
馨文
$3
138676
702
1
$a
管
$b
金談
$3
24652
801
0
$a
tw
$b
國圖
$c
20120814
$g
CCR
801
1
$a
tw
$b
國圖
$c
20120814
$g
CCR
856
# #
$u
http://handle.ncl.edu.tw/11296/ndltd/03051673664760810602
0 筆讀者評論
館藏地:
全部
六樓師生著作區 (6th Floor-Students & Faculty's Works)
七樓學位論文典藏區
出版年:
卷號:
館藏
3 筆 • 頁數 1 •
1
條碼號
典藏地名稱
館藏流通類別
資料類型
索書號
使用類型
借閱狀態
預約人數
備註欄
附件
T00930
六樓師生著作區 (6th Floor-Students & Faculty's Works)
不外借
本校學位論文
T 000 1140:2 101
一般(Normal)
在架
0
T00931
七樓學位論文典藏區
不外借
本校學位論文
T 000 1140:2 101 c.2
一般(Normal)
在架
0
T00932
七樓學位論文典藏區
不外借
本校學位論文
T 000 1140:2 101 c.3
一般(Normal)
在架
0
1張光碟
3 筆 • 頁數 1 •
1
多媒體
評論
新增評論
分享你的心得
建立或儲存個人書籤
書目轉出
取書館別
處理中
...
變更密碼
登入